There are a few possible causes if your laundry routine has slowed down as a result of your dryer taking an eternity to dry your garments. The most frequent causes of a dryer taking too long to dry clothing are covered in this article, along with suggestions for how to repair the problem.
Note: if you understand that you cannot cope with a problem on your own, contact a dryer repairman.
Is it Taking Your Dryer Forever to Dry? Typical Causes and Solutions
A fairly typical issue that the homeowner may usually resolve is that the dryer takes forever to dry. You’ll want to keep reading if your dryer needs two cycles to finish drying. We’ll go over more drying-related subjects as well, like what occurs when a dryer is overloaded and how to clean the lint screen. So you’ve found a terrific source of information if you’re having difficulties getting your clothing totally dry in one cycle.
Power Problem
If you have a gas dryer, insufficient power could be the cause of your clothing taking an eternity to dry. Electric dryers need 240 volts of power, but gas dryers need only 140 volts. You might want to purchase a washer/dryer combo machine, which takes 240 volts if your home doesn’t have enough outlets to handle a dryer.
There is too much laundry in the dryer
You may be attempting to dry too many items at once if your dryer is taking an eternity to dry your garments. A typical guideline is not to use the dryer’s capacity more than 50% of the time. Therefore, if your dryer can hold six pounds of wash, try not to load more than three pounds of wet laundry at once.
Reducing the number of garments you wash at once is another technique to prevent overloading the dryer. If you have a lot of laundry, you might want to wash them in two batches instead of one. Each load’s moisture content will be reduced as a result, and the drying process will be sped up.
Too-Wet Clothes Left in the Washer
It may also take the dryer longer to dry your garments if your washer leaves them wet. Too-wet garments take up more room in the dryer and require longer to heat up enough to evaporate the water. The dryer will have a problem leaving the garments moist as a result.
Using a high-efficiency washer is one approach to address this problem. The garments will be less damp when you put them in the dryer since these washers extract more water from the clothes than conventional machines. Make sure to choose the “extra rinse” cycle if you’re not using a high-efficiency washer so that the majority of the detergent gets washed from the clothes before drying.
Check the dryer’s lint filter
The lint screen being dirty is another typical reason why a dryer takes an eternity to dry a load of laundry. The lint screen collects all the lint and debris that falls off of the garments as they dry. It can clog up and stop airflow through the dryer vents if it isn’t cleaned frequently.
Simply remove the lint screen from the dryer and brush any extra lint or debris off. A vacuum cleaner can be used to remove any last bits of dust or debris. A dryer that takes too long to dry could benefit from the lint being removed.
Examine the dryer’s vents
If you’ve cleaned the lint screen, there might be an issue with the dryer vents, but your garments are still taking too long to dry. The dryer may overheat and take longer to dry clothing if the vents are blocked from free airflow.
Start by unplugging the dryer and removing the exhaust pipe from the back of the appliance before inspecting the dryer vents. Next, clear away any lint or debris that is obstructing the vents using a vacuum cleaner with a brush attachment. Reattach the hose and turn on the dryer after you’ve finished.
Failure of a Dryer Part
If you’ve attempted all of the aforementioned fixes for your dryer’s slow drying times, there may still be an issue with one of the dryer’s components. Your garments may take longer to dry because of a broken heating element, thermostat, or timer.
It is recommended to get a qualified repairman to look at the dryer if you suspect there might be an issue with one of the parts. Self-help attempts to solve the issue run the risk of causing further harm to the appliance and increasing overall costs.
